Bosch TDS 1216 - Manuale d'uso - Pagina 8

12

en

χПtОr tСО ТnТtТaХ 1 ЦТnutО pОrТoНμ

• “eco” setting is automatically selected.

إΝ TСОΝРrООЧΝХКЦЩΝ(η)ΝstШЩsΝضКsСТЧРέ

• The “ActiveControl Advanced” indicator lamp (3)

(МХОКrΝХТРСt)ΝРШОsΝШЧΝКЧНΝstКrtsΝضКsСТЧРέΝ

όroЦ tСТs ЦoЦОnt on, аСОn tСО СanНХО (1) oП tСО

Тron Тs РrТppОН or ТП tСО stОaЦ aМtТЯatТon Лutton (β)

Тs prОssОН at stОaЦ sОttТnРμ

• The “ActiveControl Advanced” indicator lamp (3)

stШЩsΝضКsСТЧРέ

• The pump starts working and steam is generated

automatically.

IП tСО СanНХО (1) Тs rОХОasОНμ

• Steam generation will stop.
• The “ActiveControl Advanced” indicator lamp (3) will

ضКsС

• The iron shuts off automatically. If the handle is

gripped again, the iron turns on.

IП tСО Тron rОЦaТns pХuРРОН Тn anН Тs not usОН Пor

sОЯОraХ ЦТnutОsμ

• After the handle (1) is touched or the steam activation

button (2) is pushed again, the green light starts

ضКsСТЧРέ

• Steam generation will not be possible for several

seconds, until the appropriate working temperature

has been reached.

IronТnР аТtС stОaЦ

(ζ)

TСО stОaЦ МontroХ Тs usОН to aНУust tСО aЦount

oП stОaЦ proНuМОН аСОn ТronТnР (sОО “sОttТnР tСО

stОaЦ aЦountس sОМtТon)έ

Steam can be generated in two ways :

1έ ωontТnuous stОaЦ РОnОratТon μ

• Set the steam control to “eco” or “max” position.
• Grip the handle (1).

βέ StОaЦ on НОЦanН μ

• Set the steam control to the “ ” position, to cancel

continuous steam generation while gripping the handle

(1). On this setting, steam can only be produced

when manually pressing the steam activation button

(2) under the handle.

• Press the steam activation button (2).

IЦportant μ

• Steam is only available if the temperature control (15)

is set at the steam symbols - between “••” and

“max”.

• Adjust the temperature setting and then set the

steam control according to the table below. Steam

will automatically be produced:

Temperature control (15) setting

Steam setting

••

ОМo

••• to “max”

max

Note: Once a steam ironing setting has been chosen

using the temperature control (15), steam generation

may be delayed for several seconds until the appropriate

working temperature has been reached.

IronТnР аТtСout stОaЦ

(η)

TСТs ОnaЛХОs tСО Тron to ЛО usОН Пor Нrв ТronТnРέ

• Grip the handle (1) and set the steam control to the

setting.

• The temperature control (15) adjusts the temperature

of the soleplate (13). Set it to the corresponding

position by lining it up with the temperature index (14)

on the iron.

Select an appropriate temperature for the type of

material being ironed (see “setting the temperature”

section).

• While ironing, do not press the steam activation

button (2).

Spraв

(θ)

TСТs Мan ЛО usОН to rОЦoЯО stuЛЛorn аrТnФХОsέ

• Do not use the spray function with silk as staining

may occur.

• When ironing, press the spray button (7) and water will

spray out of the spray nozzle (10) onto the garment.

SСot oП stОaЦ

(ι)

TСТs Мan ЛО usОН to rОЦoЯО stuЛЛorn аrТnФХОs or to

prОss Тn a sСarp МrОasО or pХОatέ It Мannot ЛО usОН

on a sвntСОtТМ sОttТnР Пor НОХТМatО ТtОЦsέ

• Set the temperature control (15) to the “•••” or “max”

position.

• Set the steam control to the “max” position.
• Press the shot of steam button (6) on the handle

repeatedly at intervals of 5 seconds.

VОrtТМaХ stОaЦТnР

(κ)

TСТs Мan ЛО usОН to rОЦoЯО МrОasОs ПroЦ СanРТnР

МХotСОs, МurtaТns ОtМέ It Мannot ЛО usОН on a

sвntСОtТМ sОttТnР Пor НОХТМatО ТtОЦsέ

АarnТnР!

ϊo not Тron МХotСТnР аСТХО Тt Тs ЛОТnР аorn!
ІОЯОr spraв or aТЦ tСО stОaЦ at pОrsons or

anТЦaХs!

• Set the temperature control (15) to the “•••” or “max”

position and the steam control to the position.

• Hold the iron in an upright position about 15 cm away

from the garment being steamed.

• Press the steam activation button (2). The shot of

steam button (6) on the handle may be additionally

pressed at intervals of 5 seconds. However, after

4 shots of steam, wait for 10 seconds to allow for

continued steam production.