R I C E R C A G U A S T I; SPECIFICHE TECNICHE - DeLonghi EN560 S - Manuale d'uso - Pagina 44

DE

IT

Assenza di luce sul display.

➔

Controllare l’alimentazione: presa, tensione e fusibile. In caso di problemi, contattare

Nespresso

.

Non eroga caffè, ne acqua.

➔

Il serbatoio dell'acqua è vuoto. Riempire il serbatoio dell'acqua.

➔

Decalcificare se necessario; vedere il paragrafo Decalcificazione.

Il caffè esce molto lentamente.

➔

La velocità di erogazione dipende dalla varietà di caffè.

➔

Se necessario, effettuare la decalcificazione. Fare riferimento al paragrafo Decalcificazione.

Fuoriuscita di acqua ma non di caffè (a capsula inserita).

➔

In caso di problemi, contattare

Nespresso

.

Il caffè non è abbastanza caldo.

➔

Preriscaldare la tazzina.

➔

Se necessario, effettuare la decalcificazione. Fare riferimento al paragrafo Decalcificazione.

Il vano delle capsule perde acqua (acqua nel contenitore delle capsule).

➔

Posizionare la capsula correttamente. Se si verificano perdite, contattare

Nespresso

.

Lampeggio irregolare.

➔

Far riparare la macchina o contattare il

Nespresso

Club.

Tutti i pulsanti lampeggiano contemporaneamente per 10 secondi e la
macchina si spegne automaticamente.

➔

Segnalazione di guasto. La macchina deve essere riparata. Inviare la macchina in riparazione o contattare

Nespresso

.

Tutti i 6 pulsanti lampeggiano velocemente 3 volte e poi la macchina
torna in modalità macchina pronta.

➔

Il serbatoio dell'acqua è vuoto.

Le spie per la decalcificazione e la pulizia lampeggiano.

➔

La macchina è in modalità Menu, premere il pulsante Lungo e il pulsante schiuma di latte per 3 secondi per

uscire dalla modalità Menu o attendere 30 secondi per uscire automaticamente da questa modalità.

La spia per la decalcificazione è arancione, i pulsanti per la preparazione
delle bevande sono disponibili (avviso decalcificazione livello 1).

➔

La macchina restituisce l'avviso di decalcificazione in base al consumo delle bevande. Decalcificare la macchina.

La spia per la decalcificazione lampeggia con luce arancione,
i pulsanti per la preparazione delle bevande sono disponibili
(avviso decalcificazione livello 2).

➔

Il processo di decalcificazione non è stato eseguito correttamente. Decalcificare la macchina.

La spia per la decalcificazione lampeggia con luce arancione, il pulsante
per la schiuma di latte calda è disponibile.

➔

La macchina è in modalità di decalcificazione. Premere il pulsante per il latte caldo per iniziare il processo di

decalcificazione.

La spia per la decalcificazione è arancione, i pulsanti per le preparazioni
delle bevande non sono disponibili (avviso decalcificazione livello 3).

➔

Macchina bloccata. Decalcificare la macchina.

La spia per la pulizia è arancione.

➔

Sciacquare il sistema per la preparazione del latte.

Tutti i pulsanti per la preparazione di caffè e tutti i pulsanti per la
preparazione di ricette a base di latte lampeggiano alternativamente.

➔

La macchina è surriscaldata, attendere il raffreddamento.

➔

La macchina si bloccherà per circa 10 minuti dopo lo svuotamento.

La leva non si abbassa completamente.

➔

Svuotare il contenitore delle capsule. Assicurarsi che non vi siano capsule bloccate all’interno del contenitore

delle capsule.

La qualità della schiuma di latte non è all'altezza dello standard.

➔➔

Usare latte scremato o parzialmente scremato a temperatura di frigorifero (circa 4° C).

➔➔

Risciacquare dopo ogni preparazione a base di latte (vedere la sezione Lavaggio a mano R.C.S.).

➔

Decalcificare la macchina (vedere pag. 52).

➔

Non usare latte congelato.

Non è possibile accedere alla modalità Menu.

➔

Assicurarsi di aver rimosso il contenitore del latte.

➔

Assicurarsi di premere i pulsanti Lungo e Schiuma di latte per 3 secondi.

➔

Rimuovere il tubo di decalcificazione.

R I C E R C A G U A S T I

SPEZIFIKATIONEN/

SPECIFICHE TECNICHE

LATTISSIMA TOUCH

EUR,AUS,NZ: 220240 V, 50/60 Hz, 1300 W
US/CA:

120 V, 60 Hz, 1200 W

19 bar

6.5 kg

1,38 litre

500 ml

13-16 capsules

l=19,4 cm . L=33,2 cm . h=27,4 cm

Troubleshooting

Contact the Nespressso Club

For any additional information, in case of problems

or simply to seek advise, call the Nespresso Club.

Contact details of the Nespresso Club can be found

in the 'Welcome to Nespresso' folder in your

machine box or at nespresso.com

No light on display

Check the mains, plug, voltage, and fuse. In case of problems, call the Nespresso Club.

Coffee comes out very slowly.

Flow speed depends on the coffee variety.

Perform a self check of the machine. Enter the menu list and select Maintenance. Follow instruction

Coffee is not hot enough.

Preheat cup.

Perform a self check of the machine. Enter the menu list and select Maintenance. Follow instruction

Capsule area is leaking (water in capsule container).

Position capsule correctly. If leakages occur, call the Nespresso Club.

Irregular blinking.

Send appliance to repair or call the Nespresso Club.

No coffee, just water runs out (despite inserted capsule).

In case of problems, call the Nespresso Club.

Lever cannot be closed completely

Empty capsule container. Make sure that no capsule is blocked inside the capsule container.

Quality of milk froth is not up to standard

1) For a perfect milk froth, use skimmed or semi-skimmed milk at refrigerator temperature (about 4° C)

2) Rinse after each milk based preparation. Place a recipient under milk outlet, rotate the milk

regulator knob until “CLEAN” position.

3) Every two days, disassemble the R. C. S. and clean all components in the upper level of a

dishwasher

Warranty

Delonghi warrants this product against defects in materials and workmanship for a period of two years from the date of purchase. During this period, Delonghi will either repair or

replace, at its discretion, any defective product at no charge to the owner. Replacement products or repaired parts will be guaranteed for only the unexpired portion of the original

warranty or six months, whichever is greater. This limited warranty does not apply to any defect resulting from accident, misuse, improper maintenance, or normal wear and tear. Any

defect resulting from the usage of non genuine Nespresso capsules will not be covered by this warranty. Except to the extent allowed by applicable law, the terms of this limited warranty

do not exclude, restrict

or modify, and are in addition to, the mandatory statutory rights applicable to the sale of the product to you. If you believe your product is defective, contact Nespresso for instructions on

where to send or bring it for repair. Please visit our website at nespresso.com to discover more about Nespresso

Specifications

P

max

Once the rinsing process is finished, the

machine switches off. Clean the machine

using a damp cloth. You have now finished

descaling the machine.

9

10

11

12

Rinsing process

Rinse and fill water with

fresh potable water up to MAX level.

Rinsing process

Place one container of

minimum 1 litre under both the coffee

outlet and the hot water spout.

PRESS to confirm.

The rinsing cycle continues trough the coffee

outlet, hot water spout and drip tray until the

water tank is empty.

Water hardness setting

1

programmed buttons blinks 3 times: water hardness is set

i

1”

2

3

4

1
2
3
4
5

Place the water hardness sticker under

water for 1 second.

The number of red squares indicates

the water harness level.

Set the value accordingly

Enter the menu, browse the options and select

WATER HARDNESS.

You will be guided to set the value.

Follow machine display instructions.

max

max

Kg

11

12

EUR, AUS, NZ: 220-240 V,

50-60 Hz, 1400 W

EUR,AUS,NZ: 220240 V, 50/60 Hz, 1300 W
US/CA:

120 V, 60 Hz, 1200 W

19 bar

6.5 kg

1,38 litre

500 ml

13-16 capsules

l=19,4 cm . L=33,2 cm . h=27,4 cm

Troubleshooting

Contact the Nespressso Club

For any additional information, in case of problems

or simply to seek advise, call the Nespresso Club.

Contact details of the Nespresso Club can be found

in the 'Welcome to Nespresso' folder in your

machine box or at nespresso.com

No light on display

Check the mains, plug, voltage, and fuse. In case of problems, call the Nespresso Club.

Coffee comes out very slowly.

Flow speed depends on the coffee variety.

Perform a self check of the machine. Enter the menu list and select Maintenance. Follow instruction

Coffee is not hot enough.

Preheat cup.

Perform a self check of the machine. Enter the menu list and select Maintenance. Follow instruction

Capsule area is leaking (water in capsule container).

Position capsule correctly. If leakages occur, call the Nespresso Club.

Irregular blinking.

Send appliance to repair or call the Nespresso Club.

No coffee, just water runs out (despite inserted capsule).

In case of problems, call the Nespresso Club.

Lever cannot be closed completely

Empty capsule container. Make sure that no capsule is blocked inside the capsule container.

Quality of milk froth is not up to standard

1) For a perfect milk froth, use skimmed or semi-skimmed milk at refrigerator temperature (about 4° C)

2) Rinse after each milk based preparation. Place a recipient under milk outlet, rotate the milk

regulator knob until “CLEAN” position.

3) Every two days, disassemble the R. C. S. and clean all components in the upper level of a

dishwasher

Warranty

Delonghi warrants this product against defects in materials and workmanship for a period of two years from the date of purchase. During this period, Delonghi will either repair or

replace, at its discretion, any defective product at no charge to the owner. Replacement products or repaired parts will be guaranteed for only the unexpired portion of the original

warranty or six months, whichever is greater. This limited warranty does not apply to any defect resulting from accident, misuse, improper maintenance, or normal wear and tear. Any

defect resulting from the usage of non genuine Nespresso capsules will not be covered by this warranty. Except to the extent allowed by applicable law, the terms of this limited warranty

do not exclude, restrict

or modify, and are in addition to, the mandatory statutory rights applicable to the sale of the product to you. If you believe your product is defective, contact Nespresso for instructions on

where to send or bring it for repair. Please visit our website at nespresso.com to discover more about Nespresso

Specifications

P

max

Once the rinsing process is finished, the

machine switches off. Clean the machine

using a damp cloth. You have now finished

descaling the machine.

9

10

11

12

Rinsing process

Rinse and fill water with

fresh potable water up to MAX level.

Rinsing process

Place one container of

minimum 1 litre under both the coffee

outlet and the hot water spout.

PRESS to confirm.

The rinsing cycle continues trough the coffee

outlet, hot water spout and drip tray until the

water tank is empty.

Water hardness setting

1

programmed buttons blinks 3 times: water hardness is set

i

1”

2

3

4

1
2
3
4
5

Place the water hardness sticker under

water for 1 second.

The number of red squares indicates

the water harness level.

Set the value accordingly

Enter the menu, browse the options and select

WATER HARDNESS.

You will be guided to set the value.

Follow machine display instructions.

max

max

Kg

11

12

Max/

Max.

19 bar

EUR,AUS,NZ: 220240 V, 50/60 Hz, 1300 W
US/CA:

120 V, 60 Hz, 1200 W

19 bar

6.5 kg

1,38 litre

500 ml

13-16 capsules

l=19,4 cm . L=33,2 cm . h=27,4 cm

Troubleshooting

Contact the Nespressso Club

For any additional information, in case of problems

or simply to seek advise, call the Nespresso Club.

Contact details of the Nespresso Club can be found

in the 'Welcome to Nespresso' folder in your

machine box or at nespresso.com

No light on display

Check the mains, plug, voltage, and fuse. In case of problems, call the Nespresso Club.

Coffee comes out very slowly.

Flow speed depends on the coffee variety.

Perform a self check of the machine. Enter the menu list and select Maintenance. Follow instruction

Coffee is not hot enough.

Preheat cup.

Perform a self check of the machine. Enter the menu list and select Maintenance. Follow instruction

Capsule area is leaking (water in capsule container).

Position capsule correctly. If leakages occur, call the Nespresso Club.

Irregular blinking.

Send appliance to repair or call the Nespresso Club.

No coffee, just water runs out (despite inserted capsule).

In case of problems, call the Nespresso Club.

Lever cannot be closed completely

Empty capsule container. Make sure that no capsule is blocked inside the capsule container.

Quality of milk froth is not up to standard

1) For a perfect milk froth, use skimmed or semi-skimmed milk at refrigerator temperature (about 4° C)

2) Rinse after each milk based preparation. Place a recipient under milk outlet, rotate the milk

regulator knob until “CLEAN” position.

3) Every two days, disassemble the R. C. S. and clean all components in the upper level of a

dishwasher

Warranty

Delonghi warrants this product against defects in materials and workmanship for a period of two years from the date of purchase. During this period, Delonghi will either repair or

replace, at its discretion, any defective product at no charge to the owner. Replacement products or repaired parts will be guaranteed for only the unexpired portion of the original

warranty or six months, whichever is greater. This limited warranty does not apply to any defect resulting from accident, misuse, improper maintenance, or normal wear and tear. Any

defect resulting from the usage of non genuine Nespresso capsules will not be covered by this warranty. Except to the extent allowed by applicable law, the terms of this limited warranty

do not exclude, restrict

or modify, and are in addition to, the mandatory statutory rights applicable to the sale of the product to you. If you believe your product is defective, contact Nespresso for instructions on

where to send or bring it for repair. Please visit our website at nespresso.com to discover more about Nespresso

Specifications

P

max

Once the rinsing process is finished, the

machine switches off. Clean the machine

using a damp cloth. You have now finished

descaling the machine.

9

10

11

12

Rinsing process

Rinse and fill water with

fresh potable water up to MAX level.

Rinsing process

Place one container of

minimum 1 litre under both the coffee

outlet and the hot water spout.

PRESS to confirm.

The rinsing cycle continues trough the coffee

outlet, hot water spout and drip tray until the

water tank is empty.

Water hardness setting

1

programmed buttons blinks 3 times: water hardness is set

i

1”

2

3

4

1
2
3
4
5

Place the water hardness sticker under

water for 1 second.

The number of red squares indicates

the water harness level.

Set the value accordingly

Enter the menu, browse the options and select

WATER HARDNESS.

You will be guided to set the value.

Follow machine display instructions.

max

max

Kg

11

12

~ 4.5 kg

0.9 Liter/

Litri

0.35 Liter/

Litri

17.3 cm 25.8 cm

32 cm

58

UM_LATTISSIMA_TOUCH_FACELIFT_Z2A.indb 58

19.10.17 10:01